Pneumatic ball valves
【Flanged Pneumatic Ball Valve】
Pneumatic flange ball valve is a GT-type, AT-type pneumatic piston cylinder and was 90 ° rotating ball valve directly from the combination. When the ball rotates 90 degrees, in the entrance and exit should be all spherical, thereby cutting off the flow, on the contrary both show through-hole, so that the media through.
【Pneumatic ball valve with internal thread】
Pneumatic internal thread ball valve is composed of double (single) action pneumatic piston actuator and internal thread ball valve. The valve body can be divided into integral, two-stage, three-stage.
【Stainless steel pneumatic valve】
Pneumatic stainless steel flange ball valve by the angle of pneumatic actuators and stainless steel ball valve after commissioning after the composition of some high-altitude or not allowed to have a fire source of power and other special conditions, you can achieve long-distance control or remote centralized control.
【High Pressure Pneumatic Ball Valve】
Pneumatic high-pressure ball valve is a dual (single) the role of pneumatic piston actuators and high pressure ball valve is composed of a new type of automatic control and remote control valves.
【V-type pneumatic valve】
Pneumatic V-type ball valve is divided into soft seal and hard seal according to sealing performance. It is divided into regulating type and cutting type according to regulating mode. The cutting type is divided into single action and double acting type according to the action form.
【Pneumatic Ball Valve with Handwheel】
Pneumatic handwheel ball valve is a ball valve with pneumatic actuators and worm gear manual devices, increase the worm gear manual device to prevent the valve cylinder air source state without manual operation of the valve switch to make it more secure and reliable pneumatic valve.
【Pneumatic ball valve】
Pneumatic ball valve is a pneumatic ball valve is a kind of introduction of Italian technology for the localization of the design and development of a new generation of ultra-short flange from the ball valve, the core channel shape rectangular, V-shaped and O-shaped.
【Insulated Pneumatic Ball Valve】
Pneumatic insulation ball valve has a good thermal insulation properties, and the valve diameter and diameter the same time, but also reduce the heat loss in the pipeline medium.
【Fixed Pneumatic Ball Valve】
Pneumatic fixed ball valve using the upper and lower two stem fixed. The fluid pressure does not move the ball to the valve seat during operation, and the valve seat does not deform under excessive pressure. Stem part with self-lubricating bearings, two seats are used spring preload.
【V-type Adjusting Pneumatic Ball Valve】
Pneumatic V-type regulating valve is our newly developed hard seal, PTFE sealed ball valve adjustment. It uses the spring-loaded valve seat structure, the valve seat and the ball will not produce jamming or from the other issues, reliable sealing, long service life.
【Three Way Pneumatic Ball Valve】
Pneumatic 3 way ball valve can be divided into L-and T-type. L-type three-way ball valve for medium flow switch, can make two mutually perpendicular channels connected. Three-way ball valve seat structure is generally used, according to user requirements can also be used four-seat structure.
GUQ series pneumatic vacuum ball valve is suitable for vacuum system connected to or cut off the pipeline flow in the medium. The valve to the compressed air as power, by controlling the pneumatic components to change the direction of the gas path to promote the piston rack, gear mechanical transmission to the torque output torque to drive the ball for opening and closing movement.
【O-type pneumatic valve】
Pneumatic O-cut ball valve with lip-type elastic ring structure design to ensure the reliability of sealing For low pressure, ultra-low pressure or vacuum conditions with ball valve, spring loaded seat seal structure, to ensure long-term reliable sealing ball valve. In the high temperature valve seat material can be used on the location of polystyrene or metal materials.
【Two-piece pneumatic valve】
Pneumatic two-piece ball valve is composed of pneumatic actuators and two-piece ball valve, using compressed air as energy, pneumatic signal or electrical potential to accept the attachment signal to work, with a simple structure, easy operation and so on.
【Pneumatic three-piece ball valve】
Pneumatic three-piece ball valve is small, is composed of three parts of the valve shell, by four long bolts from both ends of the middle valve body and ball. The advantage is that maintenance demolition without demolition of the pipeline thread, and the direct demolition of four bolts, the middle part of the valve can be removed. High pressure ball valve is widely used.
【Dust discharge pneumatic valve】
Pneumatic unloading sanitary ball valve sealing ring has PPL wear-resistant seals, making the seal durable.